DHD
mAirList supports DHD mixing consoles and audio cores through three interface types:
- DHD ECP for Series 52 cores and the RM4200D/RM3200D, using the External Control
Protocol via TCP/IP or serial port.
- DHD Control API for DHD cores with firmware 10.3 or newer, using the
JSON/WebSocket-based Control API.
- DHD RM2200D for the older RM2200D console.
1 - DHD ECP (Series 52, RM4200D, RM3200D)
This interface connects mAirList to DHD Series 52, RM4200D and RM3200D consoles
through the DHD External Control Protocol (ECP). It supports fader start, PFL,
channel on/off switching, motorized faders, and the exchange of logic states in both
directions.
Configuration
In the configuration app or Control Panel, go to Remote Control and add an interface
of type DHD ECP (Series 52, RM4200D, RM3200D) (DHD category).
General
- Communication:
Select either TCP/IP, and enter the Hostname or IP and Port (default 2008)
of the DHD core, or select the Serial Port that the core is connected to.
- Console/Core Type and Firmware Version:
Select Firmware 7.x or newer, Firmware 6.x, Firmware 5.x, or RM3200D.
- Fader Level Notifications:
Determines whether the core should report fader level changes to mAirList,
either Channel-based or Fader-based, or Off.
For easier configuration, export the Audio IDs, Logic IDs and Fader Channels from DHD
Toolbox to an “Ext. DHD AudioID/LogicID Export” (*.dpx) or XML Export (*.xp5) file,
and click Import Toolbox Data to import that file.
The imported data is displayed on the Logic IDs, Audio IDs and Fader Channels tabs.
It allows you to select logics and fader channels by name in the rest of the dialog
(the … and Select Fader Channel… buttons), rather than entering numeric IDs.
Players
On the Players tab, select the playlist and player, and set up the assignment:
- Automatic Setup:
Click Select Fader Channel… to choose the fader channel the player is
connected to from the imported Toolbox data. This will fill in the fields below.
- FaderStart logic or fader number:
The logic ID of the fader start, or alternatively, a fixed fader number.
- Fader channel number:
The fader channel (used for channel on/off switching, motorized faders, and
channel labels).
- PFL logic:
The logic ID for the PFL of the channel.
In the State Indication Logics table, you can enter logic IDs that are set by mAirList
to indicate the state of the player (e.g. to light up buttons on the console).
Options:
- Automatic PFL switch:
The PFL of the channel switches the PFL of the player on and off.
- Use PAUSE/STOP:
When the fader is closed, the player is paused rather than stopped.
- Keep channel on when player is paused
- Disable channel on/off switching:
By default, mAirList switches the console channel on and off along with the player.
Check this option to disable this.
- Enable motorized fader control:
Moves the motorized fader along with the player state.
- Set channel label to item title:
Displays the title of the loaded item in the channel display of the console.
Cartwall
The Cartwall Fader settings work the same as for the players (see above). When the
cartwall fader is opened, the cartwall goes ON AIR.
In the Player Logic IDs table, you can assign logic IDs to the individual cartwall
players, to start them from the console, and to indicate their state.
The options Disable channel on/off switching and Enable motorized fader control are
also available for the cartwall.
Voice Tracking
Set up the fader assignment (fader start logic or fixed fader number, or fader channel
number with firmware 6.x and up) for the voice tracking Player A, Player B, and Mic
channels.
Logic
On the States tab, you can link global mAirList states to DHD logics. For each of the
states ON AIR, PFL active, ExtPFL active, AUTOMATION 1 active, and VT active:
- Logic: The logic that is updated when the state changes in mAirList, and/or
changes the state in mAirList when it changes on the console.
- Outgoing Logic: An optional separate logic that is only set by mAirList.
- Console is master (request current state at startup):
When mAirList connects, the current state of the logic is retrieved from the console
and applied to mAirList, rather than the other way round.
- Invert: Inverts the logic state.
On the Commands tab, you can enter remote control commands to
execute when a logic (identified by its address) goes On and Off.
Monitor
The Monitor tab displays the communication with the core, which is helpful for
troubleshooting.
Actions
The following actions (DHD category) are available: Set Logic, Set PFL,
Set all PFL off, and Set Fader On/Off.
2 - DHD RM2200D
This interface connects mAirList to a DHD RM2200D console via TCP/IP. It supports fader
start and PFL for players, the cartwall, and voice tracking, as well as commands for the
console buttons.
Configuration
In the configuration app or Control Panel, go to Remote Control and add an interface
of type DHD RM2200D (DHD category).
On the Connection tab, enter the Host name or IP and the Port (default 2200)
of the console.
Players
On the Players tab, select the playlist and player, and enter either the
Fixed fader number or the Audio Source ID that the player is connected to.
When an audio source ID is used, mAirList follows the source when it is assigned to a
different fader.
Options:
- Automatic PFL switch:
The PFL of the channel switches the PFL of the player on and off.
- Use PAUSE/STOP:
When the fader is closed, the player is paused rather than stopped.
Cartwall
Enter the Fixed fader number or Audio Source ID of the cartwall fader.
In the Player Logic IDs table, you can assign logic IDs to the individual cartwall
players.
Voice Tracking
Enter the Fixed fader number or Audio Source ID for the voice tracking
Player A, Player B, and Mic channels.
On the Buttons tab, you can enter remote control commands to
execute when a button of the console is pressed (On) and released (Off).
Monitor
The Monitor tab displays the communication with the console, which is helpful for
troubleshooting.
3 - DHD Control API
This interface connects mAirList to DHD audio cores through the
DHD Control API, a JSON-based
protocol over WebSocket, which is available from DHD firmware 10.3 onwards.
It offers the same functions as the
ECP interface (fader start, PFL, channel on/off, motorized faders, logic
exchange), and additionally supports external button lists for the cartwall.
Configuration
In the configuration app or Control Panel, go to Remote Control and add an interface
of type DHD Control API (DHD category).
General
- Core Communication:
Enter the URL of the core, e.g.
http://192.168.1.100, and the API Token
configured on the core. mAirList connects to the WebSocket endpoint (/api/ws) of the
core automatically; an https:// URL results in an encrypted connection. - Number of Faders of Virtual Mixers:
Click Retrieve to read the virtual mixers and their number of faders from the core.
This information is required to select fader channels in the rest of the dialog.
Players
On the Players tab, select the playlist and player, and set up the assignment:
- Automatic Setup:
Click Select Fader Channel… to choose the fader channel the player is
connected to.
- Mixer and Fader channel number, or fader number:
The virtual mixer and the fader channel (or alternatively, a fixed fader number) that
the player is assigned to.
The State Indication Logics and the Options are the same as for the
ECP interface.
Cartwall
The Cartwall Fader settings, Player Logic IDs and Options work the same as for
the ECP interface.
External Button List for Cart Players:
Enter the List ID of an external button list configured on the core. mAirList will
fill the list with one entry per cart player, showing its number and title, colored
green when an item is loaded and red while it is playing. Pressing an entry on the
console triggers the cart player. Set to 0 to disable this feature.
Voice Tracking
Set up the fader assignment (mixer and fader channel number, or a fixed fader number) for
the voice tracking Player A, Player B, and Mic channels.
Logic
On the States tab, you can link the global mAirList states (ON AIR, PFL active,
ExtPFL active, AUTOMATION 1 active, VT active) to DHD logics, with the options
Console is master and Invert, the same as for the ECP interface.
On the Commands tab, you can enter remote control commands to
execute when a logic (identified by its address) goes On and Off.