This is the multi-page printable view of this section. Click here to print.

Return to the regular view of this page.

D&R

This section covers the integration with mixing consoles by D&R:

  • AIRENCE – USB console with built-in control switches.
  • AIRLAB – connected via serial port.
  • AIRLITE and WEBSTATION – USB consoles, controlled through the AIRLITE Control/WEBSTATION Control software by D&R.
  • AURON – connected via TCP/IP.
  • AXITE/AXUM – connected via the MambaNet protocol.

Most of these interfaces support fader start and PFL for the players, using the cartwall with the control switches of the console (including colored button LEDs), and assigning remote control commands to buttons and switches.

1 - D&R AIRENCE

The D&R AIRENCE is a USB broadcast mixer with built-in control switches. mAirList communicates with it via USB, using the airence.dll driver library that is included with mAirList.

Configuration

In the configuration app or Control Panel, go to Remote Control and add an interface of type D&R AIRENCE (D&R category).

Players

On the Players tab, select the playlist and player, and choose the USB channel used by this player (USB 1 to USB 4, or none). Opening and closing the fader of that USB channel starts and stops the player.

Options:

  • Automatic PFL switch: The PFL (CUE) button of the channel switches the PFL of the player on and off.
  • Use PAUSE/STOP: When the fader is closed, the player is paused rather than stopped.

Cartwall

Check Use control switches for cartwall to control the cart players with the control switches of the AIRENCE, and select the Buttons to use for Cartwall: the “A” Buttons, the “B” Buttons, or both (numbered either top to bottom or left to right).

The Color Settings determine how the button LEDs indicate the state of each cart player: For each player state, select a Color (off, Red, Green, or Yellow), and optionally enable Blink with a second Blink Color and a Speed.

Switches

On the Switches tab, you can assign a command to each switch (1 to 39) for when it is switched On and Off. Switches used for the cartwall are not available here.

Advanced

  • Read timeout (ms): How long mAirList waits for data from the device in each read cycle.
  • Enable debug log file: Writes a log file of the communication, for troubleshooting.

2 - D&R AIRLAB

This interface connects mAirList to a D&R AIRLAB mixing console via a serial port. It executes remote control commands when channels are switched on or off, and when the ON AIR signals of the console change.

Configuration

In the configuration app or Control Panel, go to Remote Control and add an interface of type D&R AIRLAB (D&R category).

On the Communication tab, select the COM Port that the console is connected to. The port parameters (baud rate etc.) must be set up in the Serial Ports section of the configuration first.

On the Channels tab, enter the commands to execute when a channel is switched On and Off, e.g. PLAYER 1-1 START and PLAYER 1-1 STOP for fader start.

On the On Air tab, enter the commands to execute when one of the console’s ON AIR signals goes On and Off.

3 - D&R AIRLITE

The D&R AIRLITE is a USB broadcast mixer. mAirList does not communicate with the console directly, but through the AIRLITE Control software by D&R, using its UDP API.

The D&R WEBSTATION is configured in exactly the same way.

Configuration

In the configuration app or Control Panel, go to Remote Control and add an interface of type D&R AIRLITE (D&R category).

Players

On the Players tab, select the playlist and player, and choose the USB channel used by this player, i.e. the console module that the player’s audio is connected to (or none). Opening and closing the fader of that module starts and stops the player.

Options:

  • Automatic PFL switch: The CUE button of the module switches the PFL of the player on and off.
  • Use PAUSE/STOP: When the fader is closed, the player is paused rather than stopped.
  • Send track state: Sends the state of the player to the console, e.g. to light up the module buttons.
  • Disable remote control during voice tracking: The fader does not start or stop the player while voice tracking is active.
  • Disable remote control when channel is set to Line: The fader only controls the player when the module is switched to its USB input.

Cartwall

Check Use control switches for cartwall to control the cart players with the control switches of the console, and select the Buttons to use for Cartwall (“A” Buttons, “B” Buttons, or both, numbered top to bottom or left to right).

The Color Settings determine how the button LEDs indicate the state of each cart player: For each player state, select a Color (off, Red, or Green), and optionally enable Blink with a second Blink Color and a Speed.

Additionally, you can select the USB channel used by cartwall, so that the fader of that module controls the cartwall.

Modules

On the Modules tab, you can assign commands to the functions of each module (Cue, On, Fader, Start, VT), for when the function goes On and Off.

Switches

On the Switches tab, you can assign commands to the control switches (Button 1A to Button 8B) and the Non-Stop, Mic On and Silence Detection functions, for when they go On and Off.

Advanced

The Host, UDP send port (default 19551) and UDP receive port (default 19550) for the communication with the AIRLITE Control software. The default host (127.0.0.1) assumes that the software runs on the same computer as mAirList. The ports should not be changed unless instructed by D&R support.

4 - D&R WEBSTATION

The D&R WEBSTATION is a USB broadcast mixer. Its integration works exactly the same as for the D&R AIRLITE, through the UDP API of the WEBSTATION Control software by D&R, which must be installed and running. Please refer to the D&R documentation for its installation and setup.

In the configuration app or Control Panel, go to Remote Control and add an interface of type D&R WEBSTATION (D&R category). Please see the AIRLITE page for a description of the settings.

5 - D&R AXITE/AXUM (MambaNet)

D&R AXITE and AXUM consoles use the MambaNet protocol for communication between their components. mAirList joins the MambaNet network as a node, and executes remote control commands when its actuators are switched by the console. The required mbn.dll library is included with mAirList.

Configuration

In the configuration app or Control Panel, go to Remote Control and add an interface of type D&R AXITE/AXUM (MambaNet) (D&R category).

General

  • Communication: Select how mAirList connects to the MambaNet network:
    • TCP or UDP: Enter the IP and Port (default 34848) of the console.
    • Ethernet: Communicate directly on the Ethernet layer, through the selected network Device.
  • Address and Unique ID: The MambaNet address and unique ID of the mAirList node. Each node in the network must have a unique ID; only change these values if there is more than one mAirList node.

Commands

On the Commands tab, enter the commands to execute when an actuator of the mAirList node is switched On and Off. The actuators can be assigned to console functions (e.g. buttons or fader start) in the console configuration.

6 - D&R AURON

This interface connects mAirList to a D&R AURON mixing console via TCP/IP. It supports fader start and PFL for the players, cartwall control through the console buttons (including colored LEDs), and commands for all buttons of the console.

Configuration

In the configuration app or Control Panel, go to Remote Control and add an interface of type D&R AURON (D&R category).

On the Connection tab, enter the Host name or IP of the console, and the Port (default 9000).

Players

On the Players tab, select the playlist and player, and choose the Channel used by this player (or none). Opening and closing the fader of that channel starts and stops the player.

Options:

  • Automatic PFL switch: The PFL button of the channel switches the PFL of the player on and off.
  • Use PAUSE/STOP: When the fader is closed, the player is paused rather than stopped.

Cartwall

  • Channel used by cartwall: The console channel that the cartwall is connected to.
  • Buttons to use for Cartwall: None, the “A” Buttons, the “B” Buttons, or both (numbered top to bottom or left to right).
  • Color Settings: For each cart player state, select a Color (off, Red, Green, or Yellow), and optionally enable Blink with a second Blink Color and a Speed.

Buttons

On the Buttons tab, you can assign commands to the buttons of the console, for when they are Pressed and Released. The buttons are grouped into the channel buttons, the control buttons, and the buttons of the CRM and Studio monitoring sections.